At a glance
Which area is which zone?
The table below shows the typical classification seen in this industry; the exact boundaries depend on ventilation, release sources and the ground layout and are set in your site's explosion protection document. For the zone concepts in detail, see our article on Zone 0, 1, 2 and 20, 21, 22.
| Area | Typical zone | Note |
|---|---|---|
| Underground tank interior | Zone 0 | The vapour space is a continuous explosive atmosphere. |
| Tank fill points and vent pipe outlets | Zone 1Zone 2 | Zone 1 close to the opening, Zone 2 around it. |
| Fuel dispenser | Zone 1Zone 2 | The housing interior is usually Zone 1; the surroundings and the area near the ground are usually Zone 2. |
| Tank manholes, pump pits | Zone 1 | Heavier-than-air vapour collects below ground level. |
| LPG filling point and tank valves | Zone 1Zone 2 | Zone 1 around the filling coupling and relief valve, Zone 2 beyond. |
| Inside the tank farm bund | Zone 2 | Risk of overfill and leaks; low points can be Zone 1. |
| Tanker loading / unloading gantry | Zone 1Zone 2 | Zone 1 around the loading arm and the tanker hatch. |
| Shop, office building | Safe area | Usually outside the hazardous area when separated by distance and walls. |
Gases on site and the classes they need
Rule of thumb: petrol, diesel and LPG are in group IIA; the deciding factor is usually the low ignition temperature of petrol, so choose T3 or better. LPG and petrol vapour are heavier than air: low points such as pits, trenches and manholes are classified more strictly than their surroundings.
Product groups for this industry
The links open each category with the Zone 1 + IIA filter; you can change the filter to suit your site.
Lighting
LED floodlights for canopies, loading gantries and tank farms; tank inspection lamps.
Zone 1IIA30 productsView products →Control stations
Start-stop and emergency stop stations for pumps and filling.
Zone 1IIA12 productsView products →Junction and distribution boxes
Terminal boxes for dispenser, submersible pump and level gauge cables.
Zone 1IIA17 productsView products →Cable glands
Armoured glands for buried armoured cables, blanking plugs and reducers.
Zone 1IIA7 productsView products →Conduit fittings
Sealing fittings, elbows and nipples for pump island wiring.
Zone 1IIA12 productsView products →Other products
Local isolators (safety switches) and load switches for pumps and motors.
Zone 1IIA20 productsView products →Frequently used in this industry
What to check when selecting
- The equipment category must suit the zone: at least 2 G (Gb) for Zone 1, 3 G (Gc) for Zone 2 and only 1 G (Ga) inside the tank (e.g. level sensors).
- Wherever petrol is present the temperature class must be T3 or better; T2 is enough where only LPG is present, but T3 leaves room if petrol is added later.
- For luminaires on canopies and loading gantries choose IP66 and UV-resistant housings to withstand rain and washing.
- For buried armoured cable use a certified gland that terminates the armour and suits the enclosure's protection type; a certified blanking plug in every unused entry.
- Equipment in pump pits and manholes needs a suitable IP rating against flooding, and cable ducts must be sealed against vapour migration.
Frequently asked questions
Is ex-proof equipment also needed for a diesel pump?
Diesel has a high flash point and on its own usually creates a smaller hazardous area. At stations, however, diesel and petrol usually share the same island and dispenser, so the classification follows petrol.
Is IIA equipment enough for LPG?
Propane and butane are in group IIA; equipment marked IIA, IIB or IIC can be used. If petrol is present in the same area, T3 applies for the temperature class.
Who classifies the zones?
The employer has an explosion protection document prepared under the ATEX workplace rules (Directive 1999/92/EC, in Türkiye the related regulation); the zone boundaries are set out in that document.
Sources
- Çalışanların Patlayıcı Ortamların Tehlikelerinden Korunması Hakkında Yönetmelik, Official Gazette 30.04.2013, No. 28633 (in Turkish)
- Directive 1999/92/EC, Annex I: Classification of places where explosive atmospheres may occur (legislation.gov.uk)
- Ministry of Labour and Social Security of Turkey, Implementation Guide on the Protection of Workers from the Hazards of Explosive Atmospheres (in Turkish)
- IEC 60079-10-1:2020, Classification of areas, Explosive gas atmospheres (IEC Webstore)
- HSE, Hazardous Area Classification and Control of Ignition Sources
Share the zones, fuel types and cable entries; we will send a quotation including luminaires, boxes, glands and blanking plugs.
This article is general information; your site's explosion protection document and the product certificate are decisive when selecting equipment.








